Skip to main content

pfsense 2.7.2 Setup WireGuard Site to Site Tunnel

Install WireGuard Package on Both Sites

  • On BOTH site pfsense installations, install the WireGuard package from System ---> Package Manager ---> Available Packages. Enter Wireguard in the Search term field, click search and then click on the Install button next to WireGuard package (Figure  1).

Figure 1

image.png

Create Tunnel on Site A

  • On Site A, refresh the pfsense web GUI and navigate to VPN ---> Wireguard, click on the Tunnels tab and then click on Add Tunnel button (Figure 2).

Figure 2

image.png

  • In the Tunnel Configuration fill/set in the following fields (Figure 3):
      • Enable: Checked
      • Description: Optionally, describe the purpose of this tunnel (Ex: Tunnel to Site B)
      • Listen Port: Leave blank to use port UDP/51820 or enter a specific port number you with to use
      • Interface Keys: click the Generate button to create a new Private/Public key pair and copy the Public Key that's generated in order to enter it in the Public Key field on Site B.
      • Click the Save Tunnel button

Figure 3

image.png

Create Tunnel on Site B

    • On Site B, refresh the pfsense web GUI and navigate to VPN ---> Wireguard, click on the Tunnels tab and then click on Add Tunnel button (Figure 4).

Figure 4

image.png

  • In the Tunnel Configuration fill/set in the following fields (Figure 5):
      • Enable: Checked
      • Description: Optionally, describe the purpose of this tunnel(Ex: Tunnel to Site A) 
      • Listen Port: Leave blank to use port UDP/51820 or enter a specific port number you with to use
      • Interface Keys: click the Generate button to create a new Private/Public key pair and copy the Public Key that's generated in order to enter it in the Public Key field on Site B.
      • Click the Save Tunnel button

Figure 5

image.png

Enable WireGuard on Both Sites

On BOTH sites, navigate to VPN ---> WireGuard, click on the Settings tab and click on the Enable WireGuard checkbox, select Only Unassigned Tunnels on the Interface Group Membership drop-down and then click on the Save button (Figure 6).

Figure 6

image.png

Add Peer on Site A

On Site A, navigate to VPN ---> WireGuard, click on the Peers tab and then click on the Add Peer button (Figure 7).

Figure 7

image.png

In the Peer Configuration fill/set in the following fields (Figure 8):

  • Enable: Checked
  • Tunnel: Select the Tunnel previously configured from the drop-down list
  • Description: Optionally, describe the purpose of this Peer (Ex: Peer to Site B)
  • Dynamic Endpoint: Unchecked
  • Endpoint: Fill in the Internet IP or Hostname as well as the port number for Site B
  • Public Key: Paste the previously copied Public Key from the Tunnel on Site B
  • Pre-shared Key: Click the Generate button to generate a new pre-shared key and copy it in order to paste in the Peer configuration of Site B
  • Allowed IPs: Enter an UNUSED Network address (Example: 10.10.12.0) with a CIDR of 30 (For a total of two IPs) in the first field, click the Add Allowed IP and then enter the Network Address and corresponding CIDR of the subnet for Site B
  • Click the Save Peer button

Figure 8

image.png

Add Peer on Site B

On Site B, navigate to VPN ---> WireGuard, click on the Peers tab and then click on the Add Peer button (Figure 9).

Figure 9

image.png

In the Peer Configuration fill/set in the following fields (Figure 10):

  • Enable: Checked
  • Tunnel: Select the Tunnel previously configured from the drop-down list
  • Description: Optionally, describe the purpose of this Peer (Ex: Peer to Site A)
  • Dynamic Endpoint: Unchecked
  • Endpoint: Fill in the Internet IP or Hostname as well as the port number for Site A
  • Public Key: Paste the previously copied Public Key from the Tunnel on Site A
  • Pre-shared Key:  Paste the previously copied Pre-Shared key from the Peer on Site A
  • Allowed IPs: Enter the SAME Tunnel Subnet Network address and CIDR you set on the Peer on Site A, click the Add Allowed IP and then enter the Network Address and corresponding CIDR of the subnet for Site A
  • Click the Save Peer button

Figure 10

image.png

Configure Interface for Site A

On Site A, navigate to Interfaces ---> Assignments and under Available network ports drop-down select the WireGuard tunnel you previously created and click the Add button (Figure 11).

Figure 11

image.png

Click on the new OPT(X) interface that was just created (Figure 12).

Figure 12

image.png

In the General Configuration page fill/set the following fields (Figure 13):

  • Enable: Checked
  • Description: Optionally, describe the purpose of this Interface (Ex: Tunnel to Site B)
  • IPv4 Configuration Type: Static IPv4
  • IPv4 Address: Enter an IP address for Site A. The IP address you enter here will be one of two possible IP addresses you can use from the /30 Tunnel Subnet you chose earlier. For this example, we used the Subnet Tunnel of 10.10.12.0/30 which gives us 10.10.12.1 and 10.10.12.2 as the only two usable IPs for this subnet. So, for this example we will use 10.10.12.1 for Site A.
  • Click the Save button and then click the Apply Changes button.

Figure 13

image.png

Configure Interface for Site B

On Site B, navigate to Interfaces ---> Assignments and under Available network ports drop-down select the WireGuard tunnel you previously created and click the Add button (Figure 14).

Figure 14

image.png

Click on the new OPT(X) interface that was just created (Figure 15).

Figure 15

image.png

In the General Configuration page fill/set the following fields (Figure 16):

  • Enable: Checked
  • Description: Optionally, describe the purpose of this Interface (Ex: Tunnel to Site A)
  • IPv4 Configuration Type: Static IPv4
  • IPv4 Address: Enter an IP address for Site B. The IP address you enter here will be one of two possible IP addresses you can use from the /30 Tunnel Subnet you chose earlier. For this example, we used the Subnet Tunnel of 10.10.12.0/30 which gives us 10.10.12.1 and 10.10.12.2 as the only two usable IPs for this subnet. So, for this example we will use 10.10.12.2 for Site B.
  • Click the Save button and then click the Apply Changes button.

Figure 16

image.png

Create Gateway and Route on Site A

On Site A navigate to System ---> Routing and under the Gateways tab click the Add button (Figure 17).

Figure 17

image.png

In the Edit Gateway page fill/set the following fields (Figure 18):

  • Disabled: Unchecked
  • Interface: Select the interface for Site A you created earlier
  • Name: Enter a name for this gateway (Ex: WG_GW_Site_B)
  • Gateway: Enter the Tunnel Subnet IP address for Site B. For this example we used 10.10.12.2 for Site B.
  • Description: Optionally, enter a description (Ex: Wireguard Gateway to Site B)
  • Click the Save button and then click the Apply Changes button.

Figure 18

image.pngimage.png

Next, on Site A navigate to System ---> Routing and under the Static Routes tab click the Add button (Figure 19).

Figure 19

image.png

In the Edit Route Entry page, fill/set the following fields (Figure 20)20):

  • Destination network: Enter the network subnet for Site B (NOT the tunnel subnet). In this example, the network subnet we used for Site B was 192.168.24.0/24.24.
  • Gateway: Select the Gateway to Site B you created earlier
  • Description: Optionally, enter a description (Ex: Route to Site B)
  • Click the Save button and then click the Apply Changes button.

Figure 20

image.png

Create Gateway and Route on Site B

On Site B navigate to System ---> Routing and under the Gateways tab click the Add button (Figure 21).

Figure 21

image.png

In the Edit Gateway page fill/set the following fields (Figure 22):

  • Disabled: Unchecked
  • Interface: Select the interface for Site A you created earlier
  • Name: Enter a name for this gateway (Ex: WG_GW_Site_A)
  • Gateway: Enter the Tunnel Subnet IP address for Site A. For this example we used 10.10.12.1 for Site A.
  • Description: Optionally, enter a description (Ex: Wireguard Gateway to Site A)
  • Click the Save button and then click the Apply Changes button.

Figure 22

image.png

Next, on Site A navigate to System ---> Routing and under the Static Routes tab click the Add button (Figure 23).

Figure 23

image.png

In the Edit Route Entry page, fill/set the following fields (Figure 24):

  • Destination network: Enter the network subnet for Site A (NOT the tunnel subnet). In this example, the network subnet we used for Site A was 192.168.1.0/24.
  • Gateway: Select the Gateway to Site A you created earlier
  • Description: Optionally, enter a description (Ex: Route to Site A)
  • Click the Save button and then click the Apply Changes button.

Figure 24

image.png

 

Back to top